Specials Are Our Standard

Series H – Heavy Duty Hydraulic Tie Rod Cylinders

MILWAUKEE Series “H” hydraulic tie rod cylinders are built to perform on the toughest applications. Incorporating a variety of MILWAUKEE “Exclusive” advanced features, proven through the years, these cylinders will provide a long, maintenance-free service life. Advanced engineering combined with quality materials and expert workmanship contribute to the making of a rugged, top quality hydraulic cylinder.

Series H hydraulic tie rod cylinder

Special Option Available: Consider our Patent-Pending ARC™ Technology for increasing cylinder life, automatic dearating and cylinder cooling

Special Option Available: Consider adding our Integrated Counterbalance Valve technology (ICB Series)


TIE-ROD MOUNT (Back to Top)
The flange and tie-rod mounts are basically the same, except that the cylinder tie rods are extended and used to mount the cylinder. To prevent misalignment, sagging or possible binding of the cylinder, the free end should be supported. The best use of tie-rods when extending on the blind end is in a thrust load application. When using tie-rods extended on the rod end, the best application is a tension load. Tie rod mounts are suited for many applications, but it should be noted that they are not as rigid as the flange type of mounting.

Both Ends
Model H10
NFPA MX1
1.5″ to 12″ Bore

No Extension
Model H11
NFPA MX0
1.5″ to 12″ Bore

Rod End
Model H12
NFPA MX3
1.5″ to 12″ Bore

Blind End
Model H13
NFPA MX2
1.5″ to 12″ Bore

Extended Both Ends
Model HM10
14″ to 18″ Bores

Extended Rod End
Model HM12
14″ to 18″ Bores

Extended Blind End
Model HM13
14″ to 18″ Bores


FLANGE MOUNT (Back to Top)
The flange mount is one of the strongest, most rigid methods of mounting. With this type of mount there is little allowance for misalignment, though when long strokes are required, the free end opposite the mounting should be supported to prevent sagging and possible binding of the cylinder. The best use of a blind end flange is in a thrust load application (rod in compression). Rod end flange mounts are best used in tension applications. If an application exceeds the rectangular flange rating, requiring an extra heavy flange, a solid flange style end cap mount is available at no extra cost for most bore sizes. When a less rigid mount can be used and the cylinder can be attached to a panel or bulkhead, an extended tire rod mounting could be considered.

Rod Square
Model H21
NFPA MF5
1.5″ to 12″ Bore

Blind Square
Model H22
NFPA MF6
1.5″ to 12″ Bore

Rod Rectangular
Model H31
NFPA MF1
1.5″ to 12″ Bore

Blind Rectangular
Model H32
NFPA MF2
1.5″ to 12″ Bore


SIDE AND LUG MOUNT (Back to Top)
The side or lug mounted cylinder provides a failrly rigid mount. These types of cylinders can tolerate a slight amount of misalignment when the cylinder is at full stroke, but as the piston moves toward the blind end, the tolerance for misalignment decreases. It is important to note that if the cylinder is used properly (without misalignment), the mounting bolts are either in simple shear or tension without any compound stresses.

Tapped Holes
in Caps Flush
Model H41
NFPA MS4
1.5″ to 12″ Bore

Side Lug
Model H42
NFPA MS2
1.5″ to 12″ Bore

Foot
Model H43
NFPA MS7
1.5″ to 12″ Bore

Centerline Lug
Model H51
NFPA MS3
1.5″ to 12″ Bore


PIN AND TRUNNION MOUNT (Back to Top)
All pin and trunnion cylinders need a provision on both ends for pivoting. These types of cylinders are designed to carry shear loads and the trunnion pivot pins should be carred by bearings that are rigidly held and closely fit for the entire length of the pin.

Clevis
Model H61
NFPA MP1
1.5″ to 12″ Bore

Rod End Trunnion
Model H71
NFPA MT1
1.5″ to 12″ Bore

Blind End Trunnion
Model H72
NFPA MT2
1.5″ to 12″ Bore

Center Trunnion
Model H73
NFPA MT4
1.5″ to 12″ Bore

Clevis
Model HM61
14″ to 18″ Bores

Rod End Trunnion
Model HM71
14″ to 18″ Bores

Blind End Trunnion
Model HM72
14″ to 18″ Bores

Center Trunnion
Model HM74
14″ to 18″ Bores


SOLID END CAP MOUNT (Back to Top)
Milwaukee Cylinder’s solid end cap mounts are one of the strongest, most rigid methods of mounting. Solid rod end cap mounts are best in a tension application; solid blind end cap mounts are best in a thrust load application.

Solid Rod End Cap
Model H35
NFPA ME5
1.5″ to 12″ Bore

Solid Blind End Cap
Model H36
NFPA ME6
1.5″ to 12″ Bore

Solid Rod End Cap
Model HM35
14″ Bore

Solid Blind End Cap
Model HM36
14″ Bore

Solid Rod End Cap
Model HM35
16″ and 18″ Bore

Solid Blind End Cap
Model HM36
16″ and 18″ Bore

Solid End Cap
Model HM21
14″ to 18″ Bores

Solid Blind End Cap
Model HM22
14″ to 18″ Bores


Key Mount (Back to Top)
The Milwaukee Key Mount retainer plate is a mounting option designed to add rugged stability to foot and side mount cylinders. The retainer plate is extended below the mounting surface of the cylinder. This extension may be fitted into a milled keyway in your mounting pad, eliminating the need for welded keys or locator pins.

Key Mount
1.5″ to 12″ Bore

Double Rod End (Back to Top)
Double rod end styles are available in every mounting style except clevis. On double rod end cylinders where the rod ends are not the same, be sure to specify clearly which rod end is to go at which end of the cylinder in relation to your mounting requirements.

Double Rod End
NFPA MDX
1.5″ to 12″ Bore

This website uses cookies to ensure you get the best experience. You can change your cookie settings at any time by visiting our Privacy Policy page.